How to select a Corner, Bench Or Fold Down Shower Seat

It may seem like shower seat choices are endless. So how do you make your selection from the jungle of options? Which type of seat will fit your budget, style, and supply the features and functions you desire? follow these 5 ½ steps to make the right selection for your shower remodeling project:

Step 1 – rule the size of your shower base – The size of your base is a key factor in choosing a seat. Smaller showers of 10 quadrilateral feet or less will commonly only have adequate space for a fold down or fold and store seat. For mid-sized showers (10 to 25 quadrilateral feet) the triangular shaped angle seat works well because it is ageement and functional. For larger rectangular shaped showers larger than 25 quadrilateral feet the bench seat can supply the most kind area for relaxing, shaving and showering.

Shower Seat

Step 2 – recognize the type of base/seat blend that works best – With your budget in mind value these options:

- (A) Fiberglass and acrylic seats built into the bases – Fiberglass is very cost efficient but sizes are little and if the base cracks or fails the whole enclosure must be removed. Seats are also built into acrylic bases. These bases are commonly higher potential than fiberglass but are more high-priced as well.

- (B) Wood framed base built on site – A wood framed seat buildings can be built inside a poured concrete base on site and then the buildings can be covered with whether a masonry board (most often in the case of tiled showers) or covered over with a Pvc waterproofing membrane. The benefit of this system is the potential to build it in many shapes and sizes. The disadvantage can be the labor time involved and also the risk of leakage if this factory is not done properly (transition points in the middle of the bench and the walls can be tricky).

- (C) Prefabricated vast polystyrene – This material is made of one solid unit and can be man-made into bench or angle seats. These units are ready is a wide variety of proper and institution sizes. It is waterproof, easy to work with (it is attached to the base with modified thin set), and can be fulfilled, off with tile or a solid covering material.

- (D) Fold down Brazilian walnut or teak – Fold down units are an perfect selection if you have a small shower (they use the least estimate of room). Teak has a high level of water resistance and Brazilian walnut is no ifs ands or buts 10 X great water resistance than teak.

Step 3 – consider the height and depth of your seat – The height and depth of seats can vary depending on the specific system and/or base manufacturer. commonly the height of most seats varies in the middle of a minimum of 14″ high to roughly 20″ high (for those with little mobility the 20″ high units will be better). The minimum depth of a shower seat is usually 12″ and many units are 14″ to 16″ deep as well.

Step 4 – value the waterproofing capabilities of each system – If you’re looking for a high level of water resistance in your seat there are some systems you should put on the top of your list and others you probably want to keep off the list. The winning systems for water resistance would contain acrylic base/seat combos and vast or extruded polystyrene systems. The materials to stay away from would be the institution wood made framed buildings (this is one that can be especially problematic if you or your contractor does not setup them correctly) or the fiberglass base/seat combos (these bases have the highest failure rate).

Step 5 – Top it off – The top of your seat is what is noticed the most often and will be essential to the longevity of your shower. Here are some options to consider:

- Tile seat (over whether a framed buildings or vast or extruded polystyrene) – If you pick a tile seat make sure the buildings below is well constructed and pitched slightly towards the shower drain. For best results use whether a sanded grout or for the highest level of water resistance pick a urethane grout in the middle of the tiles.

- Solid covering granite, corian, marble or cultured marble – These seats will usually be located on top of the framed or vast polystyrene systems. The nice thing about these products is they have no joints to be concerned about water penetration. The cultured marble will commonly be the most cost efficient – the genuine marble would be the most expensive.

- Teak or Brazilian walnut – The teak/Brazilian walnut seats match nicely with the earth tone color schemes being used in many showers today. While both materials are water unyielding Brazilian walnut is amazingly dense and 10 times more water unyielding than teak.

- Acrylic or fiberglass – With acrylic or fiberglass the seat will be built into the base – color selections will be limited.

Step 5 1/2- If the choices are too involved call a professional. Like many bathroom remodeling goods selections – the options are many and the choices can be daunting. If you’re unsure of what seat to use and where to use it call a expert bathroom remodeling contractor. Look for a mighty bathroom remodeling contractor straight through rating services like Angie’s List, the great company Bureau and/or tap into your group networks.

Now that you’re equipped with these 5 1/2 steps you’re ready to pick the right shower seat to perfect your bathroom project.

How to select a Corner, Bench Or Fold Down Shower Seat